Marlin_1_Piece
Marlin_1_Piece

1894 Marlin 1-Piece Firing Pin & Spring Kit by Cowboys & Indian

5 out of 5 based on 1 customer rating
(1 customer review)

$40.00

Firing pin kit for Marlin 1894 pistol caliber rifles (38/357, 38/40, 44/40, and 45LC calibers only). One piece firing pin replaces the original 3 piece pin.

1.jpg (70657 bytes) Having made sure the levergun is unloaded, remove the lever.
2.jpg (43532 bytes) Pull the lever out and then remove the bolt.  Be careful not to lose the ejector. It simply sets in a notch so be aware of it.
3.jpg (44244 bytes) The pins holding the firing pin in place must be driven out. You do not have to remove the one in the middle completely from the bolt. Remove the rear one and then drive the center one up until the firing pin comes out.
4.jpg (47429 bytes)
5.jpg (38467 bytes) Slide the new firing pin into place, making sure it is turned correctly so that the center retaining pin can be reinstalled.
6.jpg (45459 bytes)
7.jpg (100413 bytes) Remove the pin retaining the lever plunger.  Remove the old spring and install the new spring, then reinstall the lever plunger.
Reinstall the bolt and the lever in the firearm.  Then remove the stock and with the hammer down, remove the main spring.  Simply slide the mainspring retainer sideways in the slot. Don’t force it. You don’t need to bend anything. It will come out the side.
8.jpg (83222 bytes) Install the new mainspring on the hammer strut. Put the mainspring retainer on the strut, with the bottom edge inserted into the slot in the lower tang. Push the top of the retainer forward and slide it in.
Reinstall the stock and you are ready!  The difference in feel is amazing.

 

 

 

 

 

 

 

In stock

SKU: 1PcFiringPin Categories: , , Tags: , ,

Product Description

1894 Marlin 1-Piece Firing Pin Kit Cowboys & Indians

Firing pin kit for Marlin 1894 pistol caliber rifles (38/357, 38/40, 44/40, and 45LC calibers only). One piece firing pin replaces the original 3 piece pin.

These kits come with a one piece firing pin, light hammer spring, and a light lever plunger spring. The one piece firing pin eliminates the friction of the stock, two piece firing pin by eliminating the flat spring that keeps tension on the rear portion of the stock Marlin firing pin assembly, allowing for reliable firing with the lightened hammer spring. The light lever plunger spring reduces the lever sticking when your are opening it.

Kit includes: Firing Pin, Main Spring & Lever Plunger Spring.

One Piece Firing Pin for Marlin CS and ’94 Rifles
Installation Instructions:

Open lever, remove lever screw and lever. Slide bolt out of
receiver. Using a 3/32” punch, drive out two roll pins in bolt that
hold firing pin assembly. Remove all 3 pieces. Insert 1 piece
firing pin. Drive one of the roll pins into center hole of bolt,
making sure that slot in firing pin is lined up with roll pin. The
second (rear) roll pin is not used.

With Hammer down, remove tang screw then stock. Pull out
bracket and replace old spring with new spring. Re-install
bracket, stock, and screw.

Using a 1/16” punch, drive out pin holding lever detent assembly.
Replace old spring with new one and reinstall pin. Reassemble
bolt and lever from first step.

Warning: A competent gunsmith only should install these parts. All products are sold as is and without any warranty. No liability is expressed or implied for damage or injury which may result from the improper installation or use of these products.

 

Additional Information

Weight .5 lbs
Dimensions 3 x .55 x .5 in

1 review for 1894 Marlin 1-Piece Firing Pin & Spring Kit by Cowboys & Indian

  1. 5 out of 5

    (verified owner):

    Excellent product….drop in installation that smoothed up the action and eliminated all the extra oem parts….recommend this to anyone wishing to slick up the action!

Add a review